Two-Stage Injection PET Preform Injection Molding Machine
Models
|
JW-165PM
|
JW-275PM
|
|||
Injection Unit
|
|||||
Screw diameter |
mm
|
50
|
70
|
70
|
85
|
Plunger diameter |
mm
|
65
|
80
|
80
|
100
|
Injection capacity |
cm³
|
65
|
80
|
80
|
100
|
Shot size (pet) |
gr
|
810
|
1507
|
1507
|
2512
|
Plasticizing capacity |
kg/hr
|
895
|
1665
|
1665
|
2775
|
Injection rate |
cm³/sec
|
90
|
180
|
180
|
300
|
Injection pressure (max) |
kg/cm²
|
283
|
430
|
430
|
493
|
Screw speed range |
rpm
|
1076
|
1012
|
1012
|
1059
|
Screw torque |
kg-m
|
130
|
124
|
124
|
102
|
Injection stroke |
mm
|
133
|
334
|
334
|
467
|
Nozzle contact force |
tons
|
245
|
300
|
300
|
320
|
Clamping Unit
|
|||||
Clamping force |
ton
|
165
|
275
|
||
Opening force |
ton
|
16.5
|
27.5
|
||
Clamp stroke (max) |
mm
|
410
|
540
|
||
Mold height (min - max) |
mm
|
150 ~ 600
|
220 ~ 680
|
||
Open daylight |
mm
|
560 ~ 1010
|
760 ~ 1220
|
||
Platen size (H x V) |
mm
|
710 x 710
|
910 x 910
|
||
Distance between tie-rods |
mm
|
460 x 460
|
610 x 610
|
||
Hydraulic ejector force |
ton
|
8
|
16
|
16
|
32.7
|
Hydraulic ejector stroke |
mm
|
180
|
250
|
||
Hydraulics
|
|||||
Pump capacity |
1/min
|
131
|
187
|
187
|
226
|
System pressure |
kg/cm²
|
140
|
140
|
140
|
140
|
Oil reservoir capacity |
US gal
|
400
|
510
|
560
|
650
|
Electrics
|
|||||
Power supply (standard) |
volt
|
220
|
220
|
220
|
220
|
Motor rated |
HP
|
30
|
40
|
40
|
50
|
Number of heat control zones |
set
|
7
|
7
|
7
|
7
|
Heating wattage |
kw
|
18.9
|
29.2
|
29.2
|
43.9
|
General
|
|||||
Water requirements (max) |
gpm
|
18
|
18
|
18
|
21
|
Machine dimensions (LxWxH) |
M
|
5.3 x 1.43 x 2.16
|
5.82 x 1.43 x 2.16
|
6.9 x 1.72 x 2.05
|
7.5 x 1.72 x 2.05
|
Machine weight |
kg
|
6500
|
7500
|
12500
|
13500
|
Two-stage injection unit consists of one screw for pre-plasticizing and one plunger for injection
Enlarged ejector system and longer ejector stroke is especially designed to match the ejector requirement of PET preform
Copyright © 2002 by Mesin 2002. All rights reserved.